These alerts appear whenever the iPhone detects moisture inside the Lightning port. Two alerts could occur. The first alert is when we plug in our charging cable to our iPhone. Charging shuts off instantly. The second alert will appear whenever you plug in an item via its Lightning port, for example, headsets or adapters. It also blocks users from using the devices so that they won’t get damaged. Apple strongly suggests unplugging the cable to prevent corrosion from the Liquid that sits on the connector pins for the charger and accessory pins. If you need to charge the device urgently, disable the alert, and your iPhone will be charged. It is recommended to adhere to these steps until the warning disappears.
Blower the connector lightly to drain the water. Then, tap the terminal’s bottom and look for any drops of water. Then, wipe the frame using the help of a towel or cloth. It is also possible to leave your iPhone in areas with electrical current. Avoid storing it in a drawer or in an area where air cannot flow. So, the connector will be dry in a short time. Apple states that following these steps, you will need to wait around 30 minutes before the connector is dry, and then you can charge it the same way as before.
If the issue persists, you can try drying it with chilled air. The distance should be around 30 centimeters. It is suggested to move the dryer slightly towards the sides to eliminate all water out of the grooves in the speaker. Dry the frame using an oil-based cloth.
Why the Liquid Detected in Lightning Connector Error Appears
Fortunately, the Liquid detected in the lightning connector iPhone error isn’t something you should be concerned about. It’s merely a precautionary measure by the manufacturer, which disengages the lightning port if drops of water are detected inside it. It’s a security device specifically designed to stop your gadgets or device ports from being damaged by the water. There are a variety of reasons why this error might be displayed for you:
1. In humid environments, moisture can build up on the inside and around the port for charging in humid conditions. This is especially the case when you leave your phone in the bathroom while taking a shower. The humidity may get high, which can cause droplets of water to form within your charging port.
2. Rain: It’s possible you were outside in the rain, and some of the water could find its way into the charging port, causing the error.
3. Spilt drinks: An excellent way to get your phone wet is to spill something over it.
4. The issue with the software is that many Reddit users have complained that their brand-new iPhones that have not come into contact with a sticky surface or surroundings also brought the lightning port’s liquid error. This could be by a software glitch which is fortunately repaired.
Fix Liquid Detected in Lightning Connector When iPhone is Wet
Things You Should Do:
If your iPhone and Lightning accessory is submerged, you can do a couple of things to drain the water from the lightning connector.
The first step is to make sure you disconnect everything from the wall before taking it off it to prevent electrical currents from flowing through the device if it is not in use.
Then, gently tap the connector’s two sides in the direction of downwards while holding tightly so that you can drain the Liquid that is leaking from it and allow it to dry out in the air.
If you have to charge urgently, attempt to charge for at least 30 minutes. However, if you’re experiencing issues charging or connecting to your Lightning cable, you can leave your device outside in a clean location with airflow until 24 hours. Try this during this time.
Select Emergency Override
By opting to block the message rather than simply turning it off and allowing it to go away, you’ll be able to charge your iPhone despite detecting moisture in the port.
The major drawback of this solution is that you’ll likely be greeted with the same error message. If you’re not worried about repeating the message every time, it could be the solution for you.
Check whether your device is dry before performing this.
Use MagSafe Wireless Charging
Suppose the Liquid detected in the Lightning Connector popup is triggered by one of the iPhone 12 models. There is the option to switch to wireless charging. It is necessary to have a MagSafe charger to do this, however.
The truth: MagSafe charging is also an option if the presence of water is confirmed and the alert isn’t an untrue alarm. Place your phone in a dry location with low humidity for the Lightning port to dry before you attempt to charge once more.
Restart Your iPhone
If you’re having trouble following the first two steps, you need to restart your iPhone.
To turn off your device, follow these steps below:
To iPhone X and later:
Hold and press either the volume up or Down buttons and the Side/Power button.
Slide the slider to turn off your device. Wait for a minimum of 10 minutes.
Hold the Side/Power button until the Apple logo appears.
IPhone 7, 7 Plus, 8, 8 Plus, 6, and 6 Plus.
Hold and press the Power/Side button.
Slide the slider to turn off the device. Wait for a minimum of 10 minutes.
Hold the power/Side button until the Apple logo appears.
Reset All Settings
If you’re sure your iPhone is not leaking, but you have issues with the lightning connector liquid alert, it could be due to an unconfigured setting. The issue can be resolved with default settings without losing any data. Take these actions to resolve the issue.
Step 1: Open the Home screen and select the settings tab.
Step 2: Tap on General and select Reset through scrolling down.
Step 3: Click Reset All Settings. You will then enter your device’s passcode.
Step 4. The following procedure is to check the reset option. After the step is complete, verify the iPhone’s screen to see if the issue has been resolved or not.
Conclusion
If you receive the message “Liquid Detected in Lightning Connector,” you can fix it yourself if the water doesn’t have damaged internal components.
If you’re in a rush, you can try any of the methods mentioned in the article below to fix your issue in privacy at home.
If you have for your smartphone to be charged right now and you don’t have a charge via wireless, you’ll need a select Emergency override, which comes with the possibility of harming the iPhone.