Skip to content

How To Remove Mirror From Wall

    Many rooms feature big mirrors which can be without a doubt glued without delay to the wall without a body or nails. These wall mirrors are perfect because they’re cheap, easy to put in, and pose little chance of falling and breaking. Unfortunately, casting off a glued-on mirror can be a tough assignment. There are number one techniques for putting off the replicate, every of an excellent manner to leave the reflect intact for later use. For big mirrors, use a wire noticed to reduce the adhesive behind the mirror. Smaller mirrors can, without a doubt, be heated with a blow dryer or warmth gun that permits you to soften the adhesive again and motivate them to smooth to get rid of. Remember, if you remove a wall mirror, you’ll need to patch the drywall in the back.


    Removing a wall reflection is risky. If you need cushier putting off it yourself, call a glass restore organization to put it off for you.

    Some people prefer to harm the mirror with a hammer and accessible up the portions from the floor. This technique is only sometimes advocated because it may be near-impossible to get that many shards of glass off the ground.

    You can strive to decrease the reflection out of the wall if needed, but you’re probably to harm a joist. If there’s a mild above the mirror, you can also sever the wires in the wall. This is reasonably risky to do.

    Safety Considerations

    Since you will be jogging with a big glass piece, safety troubles must be considered before you begin. It isn’t endorsed to break the glass for elimination. However, it would help if you were organized for breakage. Dress in lengthy sleeves, lengthy pants, and closed-toed shoes, and put on heavy artwork gloves and eye safety at all times at equal times as you determine. Enlisting the assistance of an associate is a remarkable concept if you are getting rid of multiple replicates.


    • Heavy canvas drop cloth

    • Heat gun or blow-dryer

    • Drywall/putty knife

    • Safety glasses

    • Heavy paintings gloves (ideally leather-based-based)

    • Wire observed


    • Duct tape or packing tape


    • Protect Yourself and the Area
    • Before you begin the demolition:
    • Make sure all limitations are eliminated.

    If your replicate is over arrogance, dispose of all of the clutter from the countertop.

    Put for your protection machine, then cowl the ground or countertop with a heavy canvas drop material.

    Tape the Mirror

    Cover the replicate with strips of tape, crossing in numerous instructions. You can cowl the whole mirror or area strips of tape every few inches. The tape prevents the shards of the replication from flying everywhere if it shatters.

    Heat the Glue

    This approach works high-quality for smaller mirrors (2×2 feet or smaller). Apply warm temperature to the corners and the rims of the replicate with a warm temperature gun or blow-dryer, then work your manner closer to the middle. Hold it 6 to 12 inches from the surface of the replicate. Leave it pointed on the mirror for at least 15 mins to soften the adhesive within the once more of the mirror.

    Pry a Corner

    Slide a putty knife or drywall knife’s blade between the mirror and the drywall at the bottom corner. Place one hand under the reflection. Once the blade is in the region of most of the wall and the replicate, pull the address lightly towards you to pry the mirror off the wall. Use your other hand to maintain and guide it away from the wall as the reflection comes off. Do not be alarmed if some drywall comes off with the replicate.

    Use a putty knife to pry a corner and pull the mirror off. 

    After at least 15 minutes of warmth, take a putty knife and place your nondominant hand below the reflect. Slide the putty knife’s blade in amongst your reflect and the drywall at one of the corners at the bottom. Once the blade is in a number of the wall and the reflect, pull the take care of lightly closer to you to strain the replicate off the wall. Catch it from falling together with your non-dominant hand.[14]

    If the mirror isn’t sliding off the wall, the adhesive is, in all likelihood, quite strong. You’ll need to use a putty knife to pry those mirrors off.

    You shouldn’t need to drag it very difficult to get the mirror to boost up if you experience several resistance; locate the putty knife away and preserve heating the mirror till the adhesive melts. If the mirror doesn’t pass while you try prying it, do not practice more significant pressure. You’ll turn out to be cracking the reflect in 1/2 of. Either draw near, or a wire noticed or warm temperature it for a similarly 15 minutes earlier than attempting all over again.

    Preparing for Your New Mirror

    Whichever technique you use, there’ll probably be damage to the wall inside the lower back of the reflect. Often, this can be adhesive remnants, wherein you will want to learn how to remove rest room replicate adhesive — typically at a warm temperature or by using a manner of scraping it. There is probably scarring or damage to the drywall, mainly if you used a hammer to break the reflect.

    If you’re planning to replace the replicate with one that is identical in length or big, virtually make sure that the wall is easy enough so that they reflect can relax flush in opposition to it. Often, this means the usage of your putty knife to scrape raised bits of glue.

    If the drywall desires to be repaired, then you have a chunk of more significant paintings to do. Smooth the drywall with the use of sandpaper and your putty knife. Then, get a few spackling or joint compound and correctly sized spackle knives (huge ones for massive holes or significant harm, narrower for smaller holes), and use them to ease the spackle into holes and cracks.

    Let the spackle dry. On large jobs, you can look at how the spackle shrinks as it dries. If so, position every different coat and repeat the way till the spackle creates a smooth floor. Use a drywall sander to create an easy texture and eliminate any raised bits of spackle if essential. Then you may top, paint and deploy a state-of-the-art replicate.

    When you’re prepared to install that new, reflect, we propose placing it with clips or fasteners. It needs to be much less complicated to do away with if needed — as you can see on this post about eliminating mirrors set up with clips. Second, make sure to check out the selection of mirrors to be had here at Modern Bathroom.

    Leave a Reply

    Your email address will not be published. Required fields are marked *